Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
The article down below in relation to A Step-by-Step Guide to Installing a Bathtub is pretty much captivating. You should read it.
Setting up a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily accessible, the project can move rapidly; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub as well as do not need to alter the arrangement of your previous water supply pipelines.
Your devices and also product list must make up the following:
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the limited accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, place the tub in the needed placement. The wooden boards are useful in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub till the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Finally, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the tub has been utilized a minimum of when as this will certainly settle it into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in place between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing problems with wetness as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about How to Install a Bathtub Yourself, I assumed sharing that piece was essential. Enjoyed our content? Please share it. Let somebody else locate it. Many thanks for taking the time to read it.
Details Here Report this page